Switch 24FE PoE + 2GE + 2SFP DS-3E1326P-EI V2 Hikvision

Descripción

Switch 24FE PoE + 2GE + 2SFP DS-3E1326P-EI V2 Hikvision

General
Carcasa
Metal material
Peso neto
2.83 kg (6.24 lb)
Peso bruto
3.8 kg (8.38 lb)
Dimensiones (W x H x D)
440.00 mm × 44.00 mm × 220.80 mm (17.32'' × 1.73'' × 8.69'')
Temperatura de funcionamiento
0 °C to 45 °C (0 °F to 113 °F)
Temperatura de almacenamiento
-40 °C to 85 °C (-40 °F to 185 °F)
Condiciones de humedad
5% to 95% (no condensation)
Humedad relativa
5% to 95% (no condensation)
Fuente de alimentación
100-240 VAC, 50/60 Hz, Max. 6.3 A
Modo de instalación
Rack (equipped with mounting ears)
Max. El consumo de energía
400 W
Consumo de energía en inactivo
30 W
Surge Protection
6 kV
Parámetros de red
Puertos
24 × 10/100 Mbps PoE port,2 × Gigabit combo
Tabla de direcciones MAC
16 K
Capacidad de conmutación
Whole-Device Performance: 14.8 Gbps

Port Performance: 8.8 Gbps

Tasa de reenvío de paquetes
Whole-Device Performance: 11.01 Mpps

Port Performance: 6.55 Mpps

Caché interna
4 Mbits
Fuente de alimentación PoE
PoE Standard
IEEE 802.3af,IEEE 802.3at
Pin de alimentación PoE
8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
Puerto PoE
PoE: Ports 1 to 24
Max. Puerto de alimentación
30 W
PoE Power Budget
370 W
Función de software
Largo alcance
Ports 1 to 24: up to 300 m.

Long range performance may vary depend on camera model or cable condition.

VIP Port
Ports 1 to 8: data on VIP ports is preferentially forwarded when bandwidth resources are insufficient.
Port Isolation
Ports 1 to 24: port isolation mode to improve network security

Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.

PoE Watchdog
Ports 1 to 24: auto detect and restart the cameras that do not respond.
Link Aggregation
Link aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection.

Support static link aggregation.

Support 1 aggregation group(s).

Loop Prevention
Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default.

Support 802.1D STP.

Suppport 802.1w RSTP.

VLAN
VLAN is used for network scale planning and network health improvement.

Support 802.1Q.

Configurable VLAN ID from 1-4094.

Support Trunk, Access port mode.

Support Max. 4094 VLAN.

HPP
Support one-click activation and remote management via Hik-Partner Pro. Functions supported:

1. Display the port rate.

2. Display the port bandwidth utilization rate.

3. Display the PoE power usage.

4. Display topology information.

5. Display the alarm status.

6. Restart ports and devices.

7. Enable port long-rage mode.

8. Remotely upgrade the device.

System Maintenance
Support device management via web.

Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses.

Support Super IP, which is a fixed IP address (10.180.190.200) for direct access.

Support management via Hik-Central Pro.

Support remote management via Hik-Partner Pro.

Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected.

Supports 802.1ab LLDP for peer device discovery.

Support port mirroring for fault locating.

Certificaciones
EMC
CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020),IC (ICES-003: Issue 7:2020),RCM (AS/NZS CISPR 32: 2015)
Seguridad
CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition)), CE-LVD (EN 62368-1: 2014+A11: 2017)
Química
CE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)